MAINTENANCE SCHEDULES

CONTENTS

I Emission Control System Maintenance 262

I Maintenance Schedules 262


  1. Schedule "B"

  2. Schedule "A"

.265

.274

262 MAINTENANCE SCHEDULES

EMISSION CONTROL SYSTEM MAINTENANCE

The "Scheduled" maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability. More frequent main­tenance may be needed for vehicles in severe operating conditions such as dusty areas and very short trip driving.

Inspection and service also should be done any time a malfunction is suspected.

NOTE: Maintenance, replacement, or repair of the emission control devices and systems on your vehicle may be performed by any automotive repair establish­ment or individual using any automotive part which has been certified pursuant to U.S. EPA or, in the State of California, California Air Resources Board regulations.

MAINTENANCE SCHEDULES

There are two maintenance schedules that show the required service for your vehicle.

First is Schedule "B". It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule.

  1. Day or night temperatures are below 32°F (0°C)

  2. Stop and go driving

  3. Excessive engine idling

  4. Driving in dusty conditions

  5. Short trips of less than 10 miles (16.2 km)

  6. More than 50% of your driving is at sustained high
    speeds during hot weather, above 90°F (32°C)

  7. Trailer towing

  8. Taxi, police, or delivery service (commercial service)

  9. Off-road or desert driving

  10. If equipped for and operated with E-85 (ethanol)
    fuel.

NOTE: Most vehicles are operated under the conditions listed for Schedule "B."

Second is Schedule "A". It is for vehicles that are not operated under any of the conditions listed under Sched­ule "B."

Use the schedule that best describes your driving condi­tions. Where time and mileage are listed, follow the interval that occurs first.

CAUTION!

Failure to perform the required maintenance items may result in damage to the vehicle.

At Each Stop for Fuel

Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu­racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark.

MAINTENANCE SCHEDULES 263

Check the windshield washer solvent, add as required.
Once a Month

  1. Check the tire pressure and look for unusual wear or
    damage.

  2. Inspect the battery and clean and tighten the terminals
    as required.

  3. Check the fluid levels of the coolant reservoir, brake
    master cylinder, and transmission, and add as needed.

  4. Check all lights and all other electrical items for correct
    operation.

At Each Oil Change

  1. Change the engine oil filter.

  2. Inspect the exhaust system.

  3. Inspect brake hoses.

  4. Check the coolant level, hoses, and clamps.

  5. Inspect manual transmission fluid level if
    equipped.

264 MAINTENANCE SCHEDULES

Rotate the tires at each oil change interval shown on Schedule "A" 6,000 miles (10 000 km) or every other interval shown on Schedule "B" 6,000 miles (10 000 km).

After completion of off-road operation, the underside of the vehicle should be thoroughly inspected. Exam­ine threaded fasteners for looseness.

SCHEDULE"Â" 265

Schedule "Â"

Follow this schedule if you usually operate your vehicle under one or more of the following conditions.

  1. Day or night temperatures are below 32°F (0°C)

  2. Stop and go driving

  3. Excessive engine idling

  4. Driving in dusty conditions

  5. Short trips of less than 10 miles (16.2 km)


  1. More than 50% of your driving is at sustained high
    speeds during hot weather, above 90°F (32°C)

  2. Trailer towing

  3. Taxi, police, or delivery service (commercial service)

  4. Off-road or desert driving

  5. If equipped for and operated with E-85 (ethanol)
    fuel.



Miles (Kilometers)

3,000 (5 000)

6,000 (10 000)

9,000 (14 000)

12,000 (19 000)

15,000 (24 000)

Change the engine oil and engine oil filter.

X

X

X

X

X

Inspect the engine air filter element, replace if necessary.





X

Lubricate the steering linkage tie rod ends.

X

X

X

X

X

Lubricate the steering and suspension ball joints.


X


X


Inspect the brake linings.




X


Drain and refill the front and rear axle fluid:}:




X


266 SCHEDULE"Â"



Miles (Kilometers)

18,000 (29 000)

21,000 (34 000)

24,000 (38 000)

27,000 (43 000)

30,000 (48 000)

Change the engine oil and engine oil filter.

X

X

X

X

X

Inspect the engine air filter element, replace if necessary.





X

Inspect the PCV Valve, and replace if necessary. 0





X

Replace the spark plugs.





X

Lubricate the steering linkage tie rod ends.

X

X

X

X

X

Lubricate the steering and suspension ball joints.

X


X


X

Inspect the brake linings.



X



Drain and refill the front and rear axle fluidj



X



Inspect the transfer case fluid, add if necessary.





X

SCHEDULE"Â" 267



Miles (Kilometers)

33,000 (53 000)

36,000 (58 000)

39,000 (62 000)

42,000 (67 000)

45,000 (72 000)

Change the engine oil and engine oil filter.

X

X

X

X

X

Inspect the engine air filter element, replace if necessary.





X

Lubricate the steering linkage tie rod ends.

X

X

X

X

X

Lubricate the steering and suspension ball joints.


X


X


Inspect the brake linings.


X




Drain and refill the front and rear axle fluidj


X




Inspect the drive belt and replace as needed.





X

268 SCHEDULE"Â"



Miles (Kilometers)

48,000 (77 000)

51,000 (82 000)

54,000 (86 000)

57,000 (91 000)

60,000 (96 000)

Change the engine oil and engine oil filter.

X

X

X

X

X

Inspect the engine air filter element, replace if necessary.





X

Inspect the PCV Valve, and replace if necessary. 0





X

Inspect the ignition cables, and replace if neces­sary (2.4L Only).





X

Replace the spark plugs.





X

Lubricate the steering linkage tie rod ends.

X

X

X

X

X

Lubricate the steering and suspension ball joints.

X


X


X

Inspect the brake linings.

X




X

Drain and refill the front and rear axle fluidj

X




X

Drain and refill the automatic transmission fluid, and change filter.





X

Inspect the drive belt and replace as needed. Not required if belt was previously.





X

Drain and refill the transfer case fluid.





X

SCHEDULE"Â" 269



Miles (Kilometers)

63,000 (101 000)

66,000 (106 000)

69,000 (110 000)

72,000 (115 000)

75,000 (120 000)

Change the engine oil and engine oil filter.

X

X

X

X

X

Inspect the engine air filter element, replace if necessary.





X

Lubricate the steering linkage tie rod ends.

X

X

X

X

X

Lubricate the steering and suspension ball joints.


X


X


Inspect the brake linings.




X


Drain and refill the front and rear axle fluidj




X


Inspect the drive belt and replace as needed. Not required if belt was previously replaced.





X

270 SCHEDULE"Â"



Miles (Kilometers)

78,000 (125 000)

81,000 (130 000)

84,000 (134 000)

87,000 (139 000)

90,000 (144 000)

Change the engine oil and engine oil filter.

X

X

X

X

X

Inspect the engine air filter element, replace if necessary.





X

Inspect the PCV Valve, and replace if necessary. 0





X

Replace the spark plugs.





X

Lubricate the steering linkage tie rod ends.

X

X

X

X

X

Lubricate the steering and suspension ball joints.

X


X


X

Replace the timing belt (2.4L Only).





X

Inspect the brake linings.



X



Drain and refill the front and rear axle fluidj



X



Inspect the drive belt and replace as needed. Not required if belt was previously replaced.





X

Inspect the transfer case fluid, add if necessary.





X

SCHEDULE"Â" 271



Miles (Kilometers)

93,000 (149 000)

96,000 (154 000)

99,000 (158 000)

102,000 (163 000)

105,000 (168 000)

Change the engine oil and engine oil filter.

X

X

X

X

X

Inspect the engine air filter element, replace if necessary.





X

Lubricate the steering linkage tie rod ends.

X

X

X

X

X

Lubricate the steering and suspension ball joints.


X


X


Inspect the brake linings.


X




Drain and refill the front and rear axle fluidj


X




Inspect the drive belt and replace as needed. Not required if belt was previously replaced.





X

Flush and replace the engine coolant.




X


272 SCHEDULE"Â"



Miles (Kilometers)

108,000 (173 000)

111,000 (178 000)

114,000 (182 000)

117,000 (187 000)

120,000 (192 000)

Change the engine oil and engine oil filter.

X

X

X

X

X

Inspect the engine air filter element, replace if necessary.





X

Inspect the PCV Valve, and replace if necessary. 0





X

Replace the spark plugs.





X

Inspect the ignition cables, and replace if neces­sary (2.4L Only).





X

Lubricate the steering linkage tie rod ends.

X

X

X

X

X

Lubricate the steering and suspension ball joints.

X


X


X

Inspect the brake linings.

X




X

Drain and refill the front and rear axle fluidj

X




X

Drain and refill the automatic transmission fluid, and replace main sump filter.





X

Inspect the drive belt and replace as needed. Not required if belt was previously replaced.





X

Drain and refill the transfer case fluid.





X

Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re­ceipts.

Î This maintenance is recommended by the manufac­turer to the owner, but is not required to maintain emissions warranty.

SCHEDULE"Â" 273

^Off-highway operation, trailer towing, taxi, limousine, bus, snow plowing, or other types of commercial service or prolonged operation with heavy loading, especially in

hot weather, require front and rear axle service indicated with a | in Schedule "B". Perform these services if the vehicle is usually operated under these conditions.

274 SCHEDULE"A"

Schedule "A"



Miles (Kilometers) [Months]

6,000 (10 000)

[6]

12,000 (19 000)

[12]

18,000 (29 000) [18]

24,000 (38 000) [24]

30,000 (48 000) [30]

Change the engine oil and engine oil filter.

X

X

X

X

X

Inspect the engine air filter element, and replace if necessary.





X

Replace the spark plugs.





X

Lubricate the steering linkage joints and outer tie rod ends.

X

X

X

X

X

Lubricate the steering and suspension ball joints.


X


X


Inspect the brake linings.



X



Inspect the transfer case fluid.





X

SCHEDULE"A" 275



Miles (Kilometers) [Months]

36,000 (58 000) [36]

42,000 (67 000)

[42]

48,000 (77 000) [48]

54, 000 (86 000)

[54]

Change the engine oil and engine oil filter.

X

X

X

X

Lubricate the steering and suspension ball joints.

X


X


Lubricate the steering linkage joints and outer tie rod ends.

X

X

X

X

Inspect the brake linings.

X



X

276 SCHEDULE"A"



Miles (Kilometers) [Months]

60,000 (96 000) [60]

66,000 (106 000)

[66]

72,000 (115 000)

[72]

78,000 (125 000) [78]

Change the engine oil and engine oil filter.

X

X

X

X

Inspect the engine air filter element, and replace if nec­essary.

X




Inspect the PCV Valve, and replace if necessary. 0

X




Replace the ignition cables (2.4L Only).

X




Replace the spark plugs.

X




Lubricate the steering linkage joints and outer tie rod ends.

X

X

X

X

Lubricate the steering and suspension ball joints.

X


X


Inspect the brake linings.



X


Inspect the drive belt, and replace as needed.

X




Inspect the drive belt, and replace as needed. Not re­quired if belt was previously replaced.



X


Flush and replace the engine coolant at 60 months, re­gardless of mileage.

X




Inspect transfer case fluid.

X




SCHEDULE"A" 277



Miles (Kilometers) [Months]

84,000 (134 000) [84]

90,000 (144 000) [90]

96,000 (154 000) [96]

102, 000 (163 000) [102]

Change the engine oil and engine oil filter.

X

X

X

X

Inspect the engine air filter element, and replace if nec­essary.


X



Inspect the PCV Valve, and replace if necessary. 0


X



Replace the spark plugs.


X



Lubricate the steering linkage joints and outer tie rod ends.

X

X

X

X

Lubricate the steering and suspension ball joints.

X


X


Inspect the brake linings.


X



Inspect the drive belt, and replace as needed. Not re­quired if previously replaced.


X


X

Flush and replace the engine coolant if not done at 60 months.




X

Inspect the transfer case fluid.


X



278 SCHEDULE"A"



Miles (Kilometers) [Months]

108,000 (173 000) [108]

114,000 (182 000) [114]

120,000 (192 000) [120]

Change the engine oil and engine oil filter.

X

X

X

Inspect the engine air filter element, and replace if necessary.



X

Replace the ignition cables (2.4L Only).



X

Inspect the PCV Valve, and replace if necessary. 0



X

Replace the spark plugs.



X

Lubricate the steering linkage joints and outer tie rod ends.

X

X

X

Lubricate the steering and suspension ball joints.

X


X

Inspect the brake linings.

X



Replace the timing belt (2.4L Only).



X

Inspect the drive belt, and replace as needed. Not required if pre­viously replaced.



X

Drain and refill the transfer case fluid.



X

Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re­ceipts.

Î This maintenance is recommended by the manufac­turer to the owner, but is not required to maintain emissions warranty.